Maxi-Pedia Forum

Information Technologies and Systems (IT/IS) => Security => Topic started by: Jack on December 26, 2009, 02:38:43 am



Title: Intel Pro/Wireless 3945ABG
Post by: Jack on December 26, 2009, 02:38:43 am
Hi All,

I have the Intel Pro/Wireless 3945ABG card in my note book.

I have tried to patch the driver with ipwraw-ng-2.3.4-04022008.tar.bz2 many attempts. All fail to get it working.

I was trying with backtrack 3 and backtrack 4, all can not find the card (wlan0).

Any one could please give me some guide.

Regards,
Jack


Title: Re: Intel Pro/Wireless 3945ABG
Post by: porsche on December 26, 2009, 11:54:33 pm
Try enabling the monitor mode using

Code:
sudo airmon-ng start eth1

Or, you can get it working just by loading the builtin ipwraw driver (no patching needed).

Code:
sudo modprobe ipwraw (load new driver)
sudo airmon-ng start wlan0 (start monitor mode)

PS: I am talking Ubuntu.


Title: Re: Intel Pro/Wireless 3945ABG
Post by: Jack on December 27, 2009, 03:03:09 am
Thank you for your advice. I am using VMware Player with Backtrack 3 and Ubuntu.

I have tried the commands given and still not working. If I used iwconfig and ifconfig the screen shot is as follows:-
root@bt:~# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:0c:29:cc:00:83
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:19 Base address:0x2000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@bt:~# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

Could you advise further.

Regards,
Jack



Title: Re: Intel Pro/Wireless 3945ABG
Post by: atari on December 27, 2009, 01:19:28 pm
Hm, it looks like your adapter is not set in monitor mode.

Let's see if this guide helps:

How to crack WEP with Intel PRO/Wireless 3945ABG (http://www.maxi-pedia.com/how+to+crack+WEP+with+intel+PRO+wireless+3945ABG)

When you do lsmod, what can you see there? iwl3945, ipwraw?


Title: Re: Intel Pro/Wireless 3945ABG
Post by: Jack on December 28, 2009, 10:00:15 am
Thank you for your response.

When I do lsmod, I see ipwraw.


Reagards,
Jack



Title: Re: Intel Pro/Wireless 3945ABG
Post by: yaris on January 06, 2010, 10:53:25 pm
Hey, you need to get and install the patched ipwraw for the monitor mode to work, you can get it here:

wget http://dl.aircrack-ng.org/drivers/ipwraw-ng-2.3.4-04022008.tar.bz2


Title: Re: Intel Pro/Wireless 3945ABG
Post by: Bimmerman on January 23, 2011, 04:24:08 am
 Hi, i have (Intel PRO/Wireless 3945ABG) and i have the same problem that i cant install the ipwraw driver, i followed the steps in the link that you mentioned above in (how to crack) wep but i stopped at the step "make"  "sudo make install" when i type in the command "make" i get the following error:

WARNING: $SHELL not set to bash.Intel PRO/Wireless 3945ABG
If you experience build errors, try
'make SHELL=/bin/bash'.

make -C /lib/modules/2.6.35-24-generic/build M=/home/boody/ipwraw-ng modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.35-24-generic'

WARNING: $SHELL not set to bash.
If you experience build errors, try
'make SHELL=/bin/bash'.

  CC [M]  /home/boody/ipwraw-ng/ipwraw.o
Assembler messages:
Fatal error: can't create /home/boody/ipwraw-ng/.tmp_ipwraw.o: Permission denied
/home/boody/ipwraw-ng/ipwraw.c:43: fatal error: net/ieee80211.h: No such file or directory
compilation terminated.
make[2]: *** [/home/boody/ipwraw-ng/ipwraw.o] Error 2
make[1]: *** [_module_/home/boody/ipwraw-ng] Error 2
make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-24-generic'
make: *** [modules] Error 2

I have been searching for a solution for weeks now but i could not find a solution, please try to help me, thanks.


Title: Re: Intel Pro/Wireless 3945ABG
Post by: porsche on January 25, 2011, 08:19:42 am
WARNING: $SHELL not set to bash.
If you experience build errors, try
'make SHELL=/bin/bash'.

Hey, hello, you have to do what the message tells you. It tells you to

Code:
make SHELL=/bin/bash

This will set the shell to bash, and then it should work.


Title: Re: Intel Pro/Wireless 3945ABG
Post by: rg58sma on January 26, 2011, 12:08:08 am
I have the same error, im sure that SHELL is not the problem




Title: Re: Intel Pro/Wireless 3945ABG
Post by: dryphi on August 23, 2011, 06:57:17 am
I am getting an error when trying to make as well.
Even when I set the shell to bash (as suggested) I get "fatal error: net/ieee80211.h: No such file or directory"
I am using Ubuntu 11.04 on a Lenovo T60.
Thanks

Code:
.../ipwraw-ng$ make SHELL=/bin/bash
make -C /lib/modules/2.6.38-11-generic/build M=/home/wildcard/ipwraw-ng modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.38-11-generic'
  CC [M]  /home/wildcard/ipwraw-ng/ipwraw.o
/home/wildcard/ipwraw-ng/ipwraw.c:43:27: fatal error: net/ieee80211.h: No such file or directory
compilation terminated.
...